86-27-81802833
No. 770, Gehong Road, Gedian Development Zone, Ezhou, Hubei, China (Mainland)
Moistureproof extruded polystyrene foam blocks for house,structural insulated panel,eps concrete sandwich wall panel
Description:
BOYUEJIA sandwich wall panel is a new kind of lightweight energy saving building materials,
composited by EPS polystyrene foam, cement and sand as core materials, 5mm thickness
calcium silicate board as surface panel on both sides.
Because of its excellent performance, this wall panel becomes popular and widely used in
building new houses (such as villa, apartment, hotel, KTV, office etc.) and reforming old
partition walls recent years.
Specification:
Length (mm) | Width (mm) | Thickness (mm) | Density (kg/m2) | Application | Appearance |
2270
2440 |
610 | 50 | 38±5 |
Non-load bearing wall of houses and buildings |
With calcium silicate board as face board, solid |
60 | 42±5 | ||||
75 | 45±5 | ||||
90 | 52±5 | ||||
100 | 56±5 | ||||
120 | 62±5 | ||||
150 | 72±5 | ||||
180 | 85±5 | ||||
200 | 95±5 |
Advantages:
* Economical, environment-friendly, Energy-saving, non-harmful substance, no radiation
* Fireproof: ≥4 hours under the high temperature of 1000 degrees. Can match national standard A level
* Waterproof and wet proof: can be used for toilet, bathroom and kitchen partition wall
* Sound insulation: 38~55dB
* Lightweight and economy
* Heat preservation
* Anti-pressure, anti-quake and anti-impact
* Spiking and stickability: hanging force for single point is more than 45kg
* Increase usable area and reusable
* Fast installation and saving labor cost: 3 workers can finish 120m2/day
* Long lifespan: the prefab house made by BOYUJIA wall panels can last more than 50 years,
it is the best substitute for conventional concrete wall materials.
Application:
A) Exterior Wall
Solid and firm, high bonding strength, fireproof and thermal insulation, can keep indoor
temperature at an invariable temperature level, widely applied to various prefab house,
low buildings, apartment, villas, and city house, etc.
B) Interior Partition Wall
Sound insulation, waterproof, convenient for wire groove and water pipe inbuilt, easy to make
wall decoration, and what is more, it can enlarge using area. Widely used for offices, bedrooms,
apartments, hotels etc.
C) Floor
With the excellent performance of anti-static electricity, friction resistance, high strength,
convenient for wire groove and water pipe inbuilt, corrosion resistance, no deformation,
no split etc., this wall panel can be creatively used for floor.
D) Roof
This sandwich panel can not only solve the problem of roof leakage,
but also has the advantages of lightweight, neat joint surface, high temperature resistance, etc.
Performance Index:
NO. | Item | National Standards | Testing Results | ||||
60mm | 90mm | 120mm | 60mm | 90mm | 120mm | ||
1 | Anti-impact performance/times | ≥5 | ≥5 | ≥5 | ≥6 | ≥6 | ≥10 |
2 | Anti-bending damage load/times over deadweight | ≥1.5 | ≥1.5 | ≥1.5 | ≥3 | ≥3 | ≥3 |
3 | Anti-pressure strength /Mpa
| ≥3.5 | ≥3.5 | ≥3.5 | ≥6 | ≥6 | ≥6 |
4 | Surface density kg/m2 | ≤70 | ≤90 | ≤110 | ≤55 | ≤70 | ≤80 |
5 | Single point hanging Strength /N | ≥1000 | ≥1000 | ≥1000 | ≥1000 | ≥1200 | ≥1300 |
6 | Fire proof limit /h | ≥1 | ≥1 | ≥1 | ≥3 | ≥3 | ≥4 |
7 | Sound insulation capacity in the air /Db | ≥30 | ≥35 | ≥40 | ≥35 | ≥40 | ≥45 |
8 | Soften coefficient | ≥0.80 | ≥0.80 | ≥0.80 | ≥1 | ≥1 | ≥1 |
9 | Moisture rate a/% | ≤12 | ≤10 | ≤10 | ≤10 | ≤9 | ≤7 |
10 | Heat transfer coefficient w/m2.k | ≤2.0 | ≤2.0 | ≤2.0 | ≤1.0 | ≤0.6 | ≤0.5 |
11 | Drying shrinkage /mm/m | ≤0.6 | ≤0.6 | ≤0.6 | ≤0.45 | ≤.0.5 | ≤0.5 |
12 | Inner radiation index
| ≤1 | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 |
13 | Outer radiation index
| ≤1 | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 |
14 | Radioactivity Limit | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 | ≤1 |
Installation Steps:
1. Setting the line and carrying the board into position
2. Using hand-hold electric saw freely according to the specification of wall,
3. Sizing the bump slot and then spread the baseline and the bump slots with the Boyuejia
special adhesives
4. Carrying the board prepared to be installed to the installation place, correcting the wall board
by Special tools, and making it close tightly, and let the polymer mortar squeeze out into full and
then fixing it with a wedge temporarily
5. Correcting, fixing
Using a guiding rule of two meters to check the vertical and leveling correction. Then using 6mm
or 8mm reinforcing steel bar and ribs adding with construction sealant to fix.
6. Grooving and piping
Cutting a groove by a hand-hold electric saw for burying the concealed wire and switch box.
Then filling with polymer mortar after installation.
7. Sticking anti-cracking tape
8. Installing doorcase
9. Facing ceramic tile, decorative sheet, coating and wall paper sticking ceramic tiles,
or wood facing panels and coating directly on the installed wall without plastering.
Project Cases:
Certificates:
Factory:
HUBEI BOYUEJIA INDUSTRIAL CO., LTD is a professional manufacturer of EPS cement
sandwich panels and its relevant machinery. Factory is founded in 2009 year, located in Ezhou
City, China, occupied the area of 3000sqm, and yearly output capacity is up to 2000000sqm
wall panels and 65sets machinery,have several teams of professional operators, installers,
engineers, architects and designers, and more than 500 workers.
Exhibition Show:
Working Team:
FAQ:
Q1: Why should I choose Boyuejia panel?
A: We are a professional EPS cement sandwich panel manufacturer in China.
We have professional work team, can provide you top quality products and excellent services.
Q2: What is your approximately export amount every month?
A: Loading & shipping about 50 40GP containers per month
Q3: What is your main market?
A: Our EPS cement sandwich panels are desired all over the world, and the main market is Asia,
Africa, Middle East, South America, and developing countries.
Q4: How can I get samples for testing?
A: We will send you free samples, if you have DHL, UPS or Fedex account, that will be the best,
if have not, you can transfer the shipping cost to us, we will send the samples to you by our
shipping account.
Q5: What is your delivery time?
Normally, within 15 days. If we have the needed product in stock, can be shipped within 7 days.
For bulk order, delivery time depends on the quantity.
Q6: Do you have any certificates or qualifications?
A: Yes. We have passed CE&ISO9001. Also, we have done fireproof test, the fireproof
performance of our sandwich panel is more than 4 hours.
Welcome to your inquiry!!!